Kundencenter vServer vServerdaten/en

Aus EUserv Wiki

Wechseln zu: Navigation, Suche

Setting up a vServer

Inhaltsverzeichnis

Setting up a vServer

General

If you have an EUserv vServer, you have the possibility to comprehensively establish it in the customer service center.

You also need special parameters that you can find in the customer service center.

Reading vServerdata

In EUserv customer center, you have the opportunity to read and edit various vServerdata.

Choose your vServer contract for which you want to read or change the data.

Datei:Kc-vertrag-wählen_572x.png



Once you have selected your vServer contract, now click on "vServerdaten" under vServer.

Datei:Vserver_vertragsdetails_572x.png



Configuration data of the vServer

In the caption "Konfigurations-Daten des vServers" you will find all the data relating to the configuration of your vServer. It describes the first point of the current name of the server ("Servername: vserver.meinedomain.de").

Under "Servername (Default)" in the beginning of the system the name is automatically assigned. This name can be referred to as "Reverse-Eintrag". This is for the solution and the name Mapping with the corresponding IP in difficulties.

In the field "Haupt IP-Adresse" contains the main IP address of your vServer. This IP address has been configured during installation and must be used as the main IP. You can not change this, your server is also primarily accessible at this IP address. If you want to create extra IP addresses for your server, please use the point IP addresses. For instructions, see here.

The "Netzmaske" indicates, how many bits put out the net prefix at the beginning of the represented IP address. If the net mask is e.g., 255.255.255.0 so the net prefix is 255.255.255. - i.e. all devices in this net have the same first 3 blocks of the IP address (e.g., 127.0.0.). The separate devices differ in the last block which places at disposal in theory 254 IP addresses on the network. The "Broadcast-Adresse" serves for the communication of the devices present on the network. It is also responsible for the fact that all devices in the same network will get the relevant data. As "Default-Gateway" refers to the router, which is responsible for the network interface point. And eventually even the "Default-Passwort", which will automatically created for access to your server. For Linux derivatives this password always applies to the administrator account (root).

Datei:Vserver_vertragsdetails_572x.png



Status of vServer

In the caption "Status des vServers" you can select the three parameters on the status of your vServer. The "Server-Status" shows you whether the server runs ("running") or not available ("n/a"). The point "letzter Check" indicates when the status of the vServer last was recalled (e.g., "2012-09-20 09:00:21"). And under "Autostart-Status" you can recognize whether an automatic Reboot is activated after an operating system installation, or not.

Datei:Vserver_vserverdaten-status_572x.png



Software data of vServer

Under "Software-Daten des vServers" you get an overview, which operating system (OS) is currently installed on your vServer. You get not only information which version of the OS is installed, but also the language, whether it supports 64-bit hardware or in which phase of the Support status for the installed version.

Furthermore, you can still see which versions of Apache, PHP and MySQL software is installed. You can save it for yourself, hence, it is inconvenient to get the server side access to these software information. Additionally, it is displayed whether the installation is complete ("Installation Status") and whether the rescue system is activated.

Datei:Vserver_vserverdaten-software_572x.png



Hardware data vServer

Under "Hardware-Daten des vServers" you receive information about it on which Hostnode speaks on and which hardware of vServer is installed. This code number is a support requests of high relevance, as found quickly, which is in the context of hardware-server. The Hostnode will achieve your vServer order automatically selected by the system (depending on hardware utilization) and is not changeable by you.

Datei:Vserver_vserverdaten-hardware_572x.png