Manual Installation FreeBSD/en

Aus EUserv Wiki

Wechseln zu: Navigation, Suche

Installing FreeBSD on my root server


Installing FreeBSD on my root server


For the installation of FreeBSD you need the following software on your system:

* SSH-client (e.g. OpenSSH / PuttY)

Start FreeBSD Live System

Start the FreeBSD Live-System, see: About the FreeBSD Live-System (RescueSystem)

Log in to your server via SSH. Before starting the installation be careful that you have an updated backup of your server.

Usually all data will be deleted at the installation.

Hint: On 64bit systems the 64bit RescueSystem will always be started by default. On this system an installation in 32 and 64bit is possible.

Starting the installation

The FreeBSD installation tool Sysinstall causes some problems, so we recommend that you run the installation manually.

Preparation of the hard drives

It's important for the installation that the system knows the existing hard drives. You can check this with the following command:

# ls -1 /dev/ada* /dev/da* /dev/twed* /dev/aacd* | grep -E '[a-z]{2}[0-9]+$' /dev/ada0 /dev/ada1

This intstruction describes the installation of a hard drive with the designation "ada0". You have to replace this designation with the name of your hard drive.

Now the hard drives have to be formatted:

# gpart show
# gpart delete -i 1 ada0
# gpart destroy ada0
# gpart create -s mbr ada0
# gpart add -t freebsd -i 1 ada0

Creating the partitions with bsdlabel:

# bsdlabel -wB /dev/ada0s1
# bsdlabel -e /dev/ada0s1

# /dev/ada0s1:
8 partitions:
# size offset fstype [fsize bsize bps/cpg]
a: * 16 4.2BSD 0 0
b: 4G * swap 0 0
c: * 0 unused 0 0 # raw part, don't edit

Example-Label (4GB swap-Slice, rest for /):

This is the most simple kind of an example label. If you want to partitionize your hard disk otherwise, be careful that your partitions will be provided with the filesystem and mounted correctly. You have to customize your fstab accordingly.

Create the BSD filesystem:

# newfs -U -O2 /dev/ada0s1a

Mount the partitions:

# mount /dev/ada0s1a /mnt

Downloading the installation files:

# cd /mnt

Example FreeBSD 9.0 64bit:


Installation of the basic system:

Now the setup files are made executable and are executed after that:

# cd /mnt
#tar xjpf base.txz
#tar xjpf kernel.txz

Configuration of the system:

Installation of the Bootloader:

# #boot0cfg -B /dev/ada0

Hint: Make sure that you use the correct designation of your hard drives.

The file fstab must be created in /etc, so the slices are correctly mounted during the booting process. If you want to setup a software Raid, you can skip this step!

# vi /mnt/etc/fstab

dev/ada0s1a / ufs rw 1 1
dev/ada0s1b none swap sw 0 0

Example fstab

Activate the SSH root login:

# vi /mnt/etc/ssh/sshd_config
Here the line "#PermitRootLogin no" must be edited:

PermitRootLogin yes

(Do not forget to delete the #, so this line isn't a comment anymore)

Setting the nameserver in the resolv.conf:

# vi /mnt/etc/resolv.conf


In rc.conf the configuration of the network interface is set up and SSH is activated.

Find out of the designation of the network card:

# ifconfig

re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
inet netmask 0xffffff00 broadcast
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active

In this case the network card is "re0"

# vi /mnt/etc/rc.conf

ifconfig_re0="inet XXX.XXX.XXX.XXX netmask"

Replace "re0" with the designation of your network card.

Important: XXX.XXX.XXX.XXX has to be replaced with the IP address of your server.

The information for the IP address, the network mask and defaultrouter (Default-Gateway) can be found under your server data in the customer center.

Changing the root password:

# cd /mnt

# chroot .

# passwd

# exit

So the installation of your FreeBSD system is finished. If you want to set up a software raid 1, proceed with the next section. Otherwise you can now unmount your file systems.


# cd /

# umount /mnt

Optional: Setting up a Software Raid 1

the following points are necessary, if you want to set up a software Raid:

# echo geom_mirror_load="YES" > /mnt/boot/loader.conf

# vi /mnt/etc/fstab

dev/mirror/gm0s1a / ufs rw 1 1
dev/mirror/gm0s1b none swap sw 0 0
proc /proc procfs rw 0 0

Example fstab for a Software Raid 1

# cd /

# umount /mnt

# sysctl kern.geom.debugflags=16

# gmirror label -vb round-robin gm0 ada0

# gmirror load

# gmirror insert gm0 ada1

Check the raid:

# gmirror status

Name Status Components

mirror/gm0 DEGRADED ada0

ada1 (0%)

After all configuation steps have been finished you can restart the server via "reboot".

A few minutes later your server should be reachable via SSH and you can log in with "root" and the password you have set before.

If that works, you can restart the Rescue System. Mount your partitions (e.g. mount /dev/ada0s1a /mnt) and check the configuration of the system.

If your system is booting and everything works, you can delete the installation sources:

# rm -rf /install

Frequently Asked Questions

Q: During the mounting of the partitions the error message "Operation not permitted" appears

A: Check and repair the file system:

# fsck -t ufs -y /dev/ada0s1a